Manufacturing Of Electric Heater Elements Preparatory Work 1. Stainless Steel Tubes Blanking Chamfer Deoiling Rust Cleaning &Drying Brush Tubes Wiping Tubes 2. Electric Heating Wires Winding WireDrawing Make SilkHead 3. Lead-out Rods Blanking File Stick Milling Groove Cleaning 4. Fillers Fracture Ball Milling Sifting Magnetic Separation Drying Production Process Heating Wires Connect The Lead-out Rods Cross The Empty Tubes [...]
Cartridge Heater: Voltage: 230V; Power: 2500W; Heating zone: 590mm; Total Length: 730mm; Lending wire: 500mm; Metal Tube Material: S.S.316L; Resistance Wire: Cr20Ni80. Cartridge Heater
Technical Details: Voltage: 400v, 3Phase, 60Hz; Total Power: 18KW; Heating Tube Power: 1kw*18pcs; Tube Dia: 12mm with finns; Sheath Material: Carbon steel; Tube Material: S.S.304; Control system: PID; ATT: 3 stages. 18KW Electric Duct Heater
Technical SPECS Voltage: 380v Power: 2800W Tube Dia: 12mm Material: S.S.304 Overall Length: 3370mm
As the world’s urban areas continue to expand, an increasing number of industrial plants are being converted into construction sites for housing projects. However, many of these sites are unfit for residential use due to contamination, requiring major remediation of the soil and groundwater. This is a time-consuming and costly process, but it can now [...]
Finned Electric Heaters Specifications: Voltage: 230V; Power: 800W, 1600W, 3200W. Tube Material: S.S.304; Fin Material: S.S.304; Fin Sizes: 50*25mm, thickness 0.5mm
Cartridge Heaters Specifications: Sizes: 4.0*70 / 4.0*110 Power: 80W /100W/ 150W Voltage: 48V/ 60V/ 110V Leading Wire Length: 308mm; Unheated Connection Length: 10mm; Unheated Bottom Length: 7mm;
Specification: 20V, 200W Time to heat up to 250 ° C: 60 sec @ 5 A Wirelength 650 mm (Soft type) Wire Type: AWG #18 The cable are to have a 2 pins connector on its end. Sizes: 116*5*5mm;
HEATER ELEMENT SPECIFICATION:- EACH INDIVIDUAL HEATER ELEMENT WILL BE GIVEN A SPECIFIC PART NUMBER IDENTIFIED ON THE TRDX HEATER SCHEDULE WHICH IS TD BE MARKED DNTD THE ELEMENT PLATE BY MEANS DF AN ADHESIVE LABEL. THE PART NUMBER WILL IDENTIFY THE FOLLOWING CRITERIA OF THE HEATER ELEMENT ASSEMBLY:- BOX TYPE,BOX SIZE,HANDING,MINIMUM VELOCITY,KW RATING, VOLTAGE, PHASE [...]
ELECTRICAL SPECIFICATION: WORKING VOLTAGE: 230Vac MUST COMPLY WITH BS7671 & LVD73/23/EEC FLASH TEST WITHSTAND 1500V FOR 2 SECONDS. INSULATION RESISTANCE > 1G OHM LEAKAGE CURRENT (AT 230 Vac) < 0.1mA ELEMENT POWER TOLERANCE: ± 7.5% PERFORMANCE SPECIFICATION: SURFACE TEMPERATURE MUST NOT EXCEED 400°C IN 0.75M/S AIRFLOW. SHELF LIFE (AT NOMINAL AMBIENT TEMP & RH) > [...]
Technical Details: 1.Voltage:440V/60Hz/3 PHASE/3 WIRES; 2.Power: 800KW/100KW; 3.Heating Tubes: 20KW for each piece; 4.Tube Dia: 12mm; 5.Tube Length: 1000mm; 6.Tube Material: SUS 304; 7.Sheath Material: Carbon Steel;
Tubular Heaters for Industrial Press voltage: 380v; power: 2800w; overall length: 3370mm material: S.S.304
The heating element(also called cartridge heater) of automatic sealing machine is not heated. We must first determine what is the problem? 1. Check whether the power supply connector is loose. If it is the status of the channel, it indicates that it is the problem of the automatic sealing heater elements. 2. Check whether the [...]
Product Description Two Different Features allow the flat heater to work at a lower sheath temperature than a equally powered round tubular element: Flat surface Because of its design,flat tubular heaters will heat viscous fluids from ambient temperature faster than round tubular heater elements with the same wattage and at a lower sheath temperature. The [...]
PTC Heater is an automatic constant temperature, power saving heater. It is a heater made of PTC thermistor ceramic elements as heat source, corrugated sheet made of aluminum alloy as radiator, which is bonded and welded. PTC heater of electric air conditioner generally includes MCU processor, power module MOSFET / IGBT, isolation pre drive and [...]
U shape Heater Element 1KW Heater Spec: 220V, 1KW, 2P Material: S.S. 304 Hot ire: FCHW-2 w φ0.45 MGO:MTVF-1 Electroly tic polishing; Insulation Resistance Infinity with stand voltagetest:1500V/1min
Finned Sheathed Hairpin Heater Element ELECTRICAL SPECIFICATION: WORKING VOLTAGE: 230Vac MUST COMPLY WITH BS7671 & LVD73/23/EEC FLASH TEST WITHSTAND 1500V FOR 2 SECONDS. INSULATION RESISTANCE > 1G OHM LEAKAGE CURRENT (AT 230 Vac) < 0.1mA ELEMENT POWER TOLERANCE: ± 7.5% PERFORMANCE SPECIFICATION: SURFACE TEMPERATURE MUST NOT EXCEED 400°C IN 0.75M/S AIRFLOW. SHELF LIFE (AT NOMINAL [...]
PTC Heaters 1500W Technical Details： Length*Width*Height: 220mm*35mm*18mm; Power & Voltage: 1500W, 220V； Material: Ceramic Isolation: Aluminum tubes
X-type Heater Element Technical SPECS: Voltage: 220V; Power: 250W; Sizes: 200mm* 110mm * 30mm; Leading Wire: 16# Braiding Wires; Length 400mm, with 250#terminal connectors; Mounting Holes: 4 holes, 20mm from the sides. Mark: 220V, 250W; Material: Aluminum.
Finned Tubular Heater Element Technical SPECS: Voltage: 254V, 60Hz; Power: 1KW; The insulation resistance of components in cold state(25℃) shall not be less than 100MΩ; In hot state shall not be less than 30MΩ; The insulation resistance shall not be less than 5MΩ when the humidity is less than or equal to 90%； Tube Dia: [...]
Hot Pot Electric Heater Elements Technical SPECS Tube Material: SUS304; Thickness: 0.4mm Withstand Voltage: 1800V/0.5mA/1sec; Cold Insulation: >100MΩ; When the rated voltage is used, the leakage current shall not exceed 0.5mA. Flatness: <1.9mm; Dimensions Unit: mm; Voltage: 230V; Power: 1500W; Length: 1634mm;
SZK-30 30KW Melt blown Heater Techncial File Equipment Type: SZK-30; Working principle of equipment; The air heater is a new type of environmental protection heat energy conversion equipment. Its working principle is: using electric power as energy and air as medium to heat through the heater, so as to achieve the purpose of continuously obtaining the [...]
Fryer Electric Heater Element Technical Details: voltage: 240v Power: 5000w Tube material: Stainless Steel 304 The terminal must be with 3.95mm thread nut, pressure washer, two washers, porcelain, 15.90mm thread nut, gasket, 22.26mm flange.
Electric Duct Air Heater Technical Details: Voltage: 400V, 3Ph, 60Hz; Power: 18KW; Tube Power: 1KW; Tube QTY: 18pcs * Dia 12mm with finns; Sheath Material: Carbon Steel; Tube Material: S.S>304; Control: PID System; Att: 3 stages.
Electric air duct heaters Technical Details: Voltage: 380V, 3Ph, 60Hz; Power: 4KW; Heater Elements QTY: 4pcs*4KW; Heaters' Dia: 12mm; Heaters' Length: 500mm; Haters' Material: S.S.304; Sheath Material: S.S.304; No. Of Stage: 4 stages; Control System: PID system.
TUBULAR ELEMENT NOTES: DIMENSIONS IN INCHES MATERIAL: INCOLOY 800, OD: 0.430" 1 TURN TROMBONE TROMBONE CENTERLINE BENDING RADIUS: 1.715" BRAZED SS BULKHEAD SEALED ENDS 10/32 THREADED ENDS HEATED ELEMENT LENGTH: about 32.6" MAX POWER 2.8 kW, ABOUT 64 W/in^2 (10 W/cm^2)
Tubular Coil: R01 IER Coil 0.430T 5N 0.85P 5D1 2.5D2 NatEnds Incoloy 800 0.430" TUBULAR DIAMETER 5.5" COIL BENDING DIAMETER (CENTER TUBE) 0.850" COIL PITCH 5 TURNS COIL BRAZED BULKHEADS SS304, 5/8-18 UNF WITH SEALED ENDS 10-32 THREADED STUDS FOR ELECTRICAL CONNECTION TUBULAR LENGTH: 116" ACTIVE HEATING LENGTH: 101" COIL LENGTH: about 116" HEATED ELEMENT [...]
Technical Details: Rating: 240V, 1500W; SHEATH:INCOLOY 800,THICKNESS:0.5mm. Hi-POT TEST:1500V/S MIN COLD CONDITION,CUT OFF CURRENT:0.75mA. INSULATION RESISTANCE: 10MΩ MIN COLD CONDITION; LEAKAGE CURRENT TO BE 0.75mA MAX.WHILE ENERGIZED AT RATED VOLTAGE. PROCESS:IN OIL. HEATER FULLY ANNEALED.
The wound finned electric heating tube and the square finned electric heating tube belong to the electric heating tube of air dry burning, which can be used in industrial equipment such as oven, paint baking room and pipe heating, as shown in the figure below: Only from [...]
Technical Requirements： 1.Standards：The electric heater is designed and manufactured in strict accordance with JB / t2379-93 standard. Explosion proof electric heater is designed and manufactured in strict accordance with gb3836.1 ~ 3-2010 standard. 2.Rated Voltage：415V, 3 Phase, 50Hz. 3.Power：68KW（3 steps）. ∅11 U-type heating tubes 9pcs，7.55KW/pc. 4.Heating Media：Air； Designed Temp：110℃; Working Temp:90℃. 5.Designed Pressure：1.2MPa； Working Pressure：1.0MPa [...]
Flange Heaters: Explosion Proof: Exd IIC T6 IP Rating: IP66 Operating Press: Atm. Operating Temp: 45 C Degrees. Voltage: 400V, 3P, 50Hz. Watt: 50KW. Heat Flux: 3.2W/cm2; Heating Medium: Glycol solution(50%)+H2O; Material Of Heating Element: S.S.316L.
Dry burning electric heating tube is special, the material is not fixed, it is based on the heated temperature to determine what material of electric heating elements to use. In order to ensure the service life, the corresponding temperature control must be carried out. Air dry burning, hot air circulation and drying process: [...]
The surface temperature of the electric heating element is the heat generated by the heating wire passing through the magnesium oxide powder filled in the heating tube, which penetrates into the tube body. At this time, the surface of the heating tube has a temperature. How to know the surface temperature of the electric [...]
Features The air Pipe heater is an electric heating device that primarily heats a gas stream. 1、High thermal efficiency. 2、Heat up and cool fast. 3、Fast adjustment but stability. 4、Durable and long service life. 5、Air clean and small volume. 6、Non-standard custom. Descriptions Heat the required air from the initial temperature to the set temperature. [...]
I Model: SZF-250 II Equipment Feature This kind of Thermal Oil Heater is a kind of new-typed heating equipment with heat energy conversion. It takes the electricity as power, air as the medium. The air is forced to be blown into the heater for heating through the fan, to meet the purpose of continuously obtaining the [...]
The structure of the internal wire cartridge heater is that the high temperature lead is welded directly from the inner to the resistance wire. So, this leading wire temperature of this structure should be at least 800 degrees, and such leading wire normally used is pure nickel wire. The process cost of this way is high, [...]
OVERVIEW Cartridge heaters can be treated as “component heaters” that are used to generate heat in many areas. These heaters are widely used in the mold, dies, plates, hot stamping, plastic molding, food processing, packaging machinery, sealing, extruders, crankcase heating, hot runner molds, hot melt adhesives, process tanks, laboratory apparatus, cleaning tanks and die blocks. [...]
The term of heating elements is the first thing we need to know about heating industry. Today, SZ Heat Technical Department lists some main heating pipe terms for your reference: Heating Tube Lead Rod (Line) The lead-out rod (line) of heating elements refers to the metal conductive parts which are connected with the heating body [...]
Heating tubes are usually divided into civil heating tubes and industrial heating tubes. The industrial heaters are always non-standard products, and the structures are various. And the designment of structure is usually convenient for the installation of heating equipments, so we should pay attention to many aspects when designing the structure of heating pipes. According [...]
Customers often ask me: If 220V 1000W, what electric heating tube temperature is the highest? This question seems simple but difficult to answer. Because the temperature of the electric heating tube is related to many factors. Today, I would like to tell you what electric heating tube has the highest temperature. ♠ Heating Medium [...]
Electric heating tubes can be divided into embedded heating and bare air heating in the working environment for dry burning. So what is the difference between these 2 heating methods? Does it affect the design of heating elements? Here are the answers: ♣ Core difference: Heat transfer efficiency is different. [...]
Many customers will be panicked when the heating elements of the fermenter turns red, fearing that the electric heating tubes will explode or burn out. In fact, this does not need to worry at all. Let me explain to you how the red heating tube will turn red. Each electric heating tube has [...]
In our daily life, we should encounter that the water heating tubes are overheated fast without completely insert into the water, and soon the heating tube will burn red and black, and finally stop working. Now, I would like to explain to you how the electric water heating tubes are heated exposed outside. This [...]
